Cart

Cart

photo

Active Step

To turn steps on or off, activate the Step Mode in the Section Controls. The step select buttons indicate which steps are active. Steps that are deselected behave as set in the Skip Step Mode Menu.  

Read More

Clock In

With the Clock In you can set the speed of the individual sequencers via an incoming clock signal. Overrides the Speed rotary control per sequencer. You can use one clock source for multiple sequencers by daisy chaining the Clock Out to the other sequencer’s Clock In. When using the MIDI In (and subsequently the MIDI Clock Out) as your […]

Read More

Clock Out

The Clock Out jack outputs the clock per sequencer as set by Speed or incoming clock. You can use one clock source for multiple sequencers by daisy chaining the Clock Out to the other Sequencer’s Clock In. When using the MIDI In (and subsequently the MIDI Clock Out) as your master clock source, you need to select the […]

Read More
photo

CV Out

The CV Out is the output of the sequencers. It outputs 2V, 5V or 9V as set with the Output Range slide switches. The output can be quantized with the Quantizers, effectively giving you a range up to 9 Octaves. The output is also affected by the Transpose In.

Read More
photo

Division

The Division Control sets the division of the Speed or incoming clock at which the sequencer will run. When syncing sequencers to one another, patch the Clock Out to the Clock In. When you then set the Division of the sequencer you would like to sync to the same setting as the master clock source, the sequencer operates at the […]

Read More
photo

Gate

After engaging the Gate function in the Section Controls, you can use the 16 step select buttons of each sequencer to set the steps for which a gate signal is sent over the Gate Output. The Komplex Sequencer’s Gate signals are +5V. In the current firmware minimum Gate Length is 7 milliseconds, maximum Gate Length is […]

Read More
photo

Gate Length

The Gate Length rotary control sets the pulse width of the gate signal coming from the Gate Out. Animation of the Gate Length per step can easily be achieved by sending a CV signal of 0V to +5V to the Gate Length CV Input, of which the Gate Length knob will set a bias.  

Read More

Gate Out

The Gate out jack outputs a +5V gate signal where a Gate step is engaged on the step select buttons in Gate Mode on each sequencer. The length of the gate can be controlled by the Gate Length knob per sequencer or by control voltage of the Gate Length In.

Read More
photo

Glide

To select the steps on which Glide is active, first select Glide in the Section Controls and chose your steps. The Glide rotary control per sequencer sets the portamento time for steps in which glide is active. Can be used for acid-style slides! Animation of the Glide per step can easily be achieved by sending a CV signal of 0V to +5V […]

Read More

Knobs and Buttons Overview

PER SEQUENCER CONTROLS [col2]A. CV Slider Sets the output amount of CV per step. B. Step Select Button Multi-function control for per step selection of the Section Controls. C. Speed  Sets the tempo of the sequencer. D. Seq Length Sets how many steps the sequencer will play until it resets back to the sequence start […]

Read More
photo

Mode Menu

When the Mode Menu button is pressed, you enter the Mode Menu. In this menu you can set the behavior of all the different functions of the Komplex Sequencer. Find the overview of all the current features in the Mode Menu Manual below:

Read More
photo

One-Shot Mode

When One-Shot Mode is engaged, the selected sequencer (A,B,C,D) will only run once until Play or Global Play / Pause is pressed again or when it receives a trigger at the Start CV Input.

Read More
photo

Output Range

To set the voltage Output Range per sequencer, flip the slide switch per sequencer to choose between 2, 5 and 9 volts. The corresponding voltage will be applied to the CV Output.

Read More
photo

Play Mode

Use the rotary control for Play Mode to set the order in which the steps are played, the different options are: Forward; Reverse; Ping Pong; Ping Pong Reverse; Random. This you can set per different sequencer. You can also control the Play Mode per sequencer by sending a control voltage to the Play Mode CV Input. […]

Read More
photo

Play Mode In

Control voltage into the Play Mode In selects between the different Play Modes: forward, reverse, ping-pong, ping-pong reverse and random. This input sets a bias to the rotary control’s position. Here are the values for the Play Mode CV Input:

Read More
photo

Quantizer

The four quantizer slide switches scale the selected sequencer CV Output to V/oct, selectable in chromatic, major and minor scales. Use the on/off buttons to switch the quantizer on or off per sequencer.

Read More
photo

Repeat Set

After engaging the Repeat Set function in the Section Controls, you can use the Step Select Buttons to select which steps will repeat and configure how many times they will be repeated. The Komplex Sequencer has two repeat modes: Normal Repeat Mode (the selected step gets repeated in the same tempo as the sequence) or Ratcheting Repeat Mode, […]

Read More